Ricoh EMP 156 Bedienungsanleitung

Multi Protocol NIC forDDP70/92 and EMP 156Installation Instructions© 2007 Ricoh Corporation5 Dedrick PlaceWest Caldwell, NJ 07006January 2007N336649B

7/556. Touch “Upgrade System” button.　　　　　7. Touch the Enter button without inputting any Keycode because it is already set. The printer starts proc

8/558. After the completion of upgrade preparation, the New Print Server Software Version is displayed on "New version" of the Print Serve

9/5510. The following screen is displayed after skipping all other upgrade screens except the Print Server. Turn off and on the printer to restart

10/553. The input screen of “System Password” is displayed. Press the Enter button to enter “System” menu without inputting the system password(facto

11/557. The input screen of “IP Address” is displayed. Press the IP Address(as user’s environment) using ten keys, then touch the Enter button.8. To

12/55Reset to Factory Default of the Controller configuration and the Network Board Ass’yCAUTION!When Factory Default is executed, please note that t

13/554.Click the “Reset”.5.Check the “Complete Reset” and click the “Submit”.ResetSubmit

14/556. After the above-mentioned operation is executed, the following screens are displayed in OCP of the printer. Then execute power cycle the p

15/554. Touch the Next Screen button once to display the next screen, and touch "Backup/Restore” button.5. Touch the “Backup” button, and touch “

16/557. Touch the Exit button.8. Execute the “Set IP Address of the Network Board Ass’y”(page 9) again.9. Execute the “Print Status Page”(page 2) agai

© 2007 Ricoh Corporation. All rights reserved.No part of this document may be reproduced without the expressed permission of RicohCorporation.The mate

17/55Continuation of Table 1*1 : It is displayed when the optional item(s) are installed.Items Factory DefaultOCP：Printer MenuDefault Output Elevator

18/55Continuation of Table 1*1 : It is displayed when the optional item(s) are installed.*3 : It is displayed when the values other than "Postscr

19/55Continuation of Table 1*1 : It is displayed when the optional item(s) are installed.*3 : It is displayed when the values other than "Postscr

20/55Continuation of Table 1*1 : It is displayed when the optional item(s) are installed.*3 : It is displayed when the values other than "Postscr

21/55Continuation of Table 1*1 : It is displayed when the optional item(s) are installed.*3 : It is displayed when the values other than "Postscr

22/55Continuation of Table 1*1 : It is displayed when the optional item(s) are installed.*3 : It is displayed when the values other than "Postscr

23/55Continuation of Table 1*1 : It is displayed when the optional item(s) are installed.*3 : It is displayed when the values other than "Postscr

24/55Continuation of Table 1*1 : It is displayed when the optional item(s) are installed.*3 : It is displayed when the values other than "Postscr

25/55Continuation of Table 1Items Factory DefaultWeb：Manage - Configuration MenuCompany Legal Name (blank)Phone Number (blank)Fax Number (blank)Street

26/55Continuation of Table 1Items Factory DefaultWeb：Manage - Configuration Menu106/206 4ID20107/207 4106/206 5ID21107/207 5106/206 0Configuration Mis

RevisionsRevision Page No. (Contents) DateA Original Release October 2005B Generic Release - adds title page and copyright page January 2007

27/553. Installing for the EMP156 Note: The GND Plate(LBM) and the ferrite core are not used for EMP156.Print the Status Page Please print the Sta

28/55Accessing the Controller Assembly1. Make sure you have shut down the printer and unplugged the power cable from the wall.2. Remove all external

29/555. Unplug the HDD cable from controller board connector J6.6. Unplug the FAN cable from controller board connector J21.7. Unplug the HDD power

30/553. Attach the Dust Cover/D Sub Type(Installation Requirements No.3) to the MGMT of the NetworkBoard Ass’y, and attach the Dust Cover/Modular Typ

31/55Installing the CE box cover and the Rear cover(R)1. Plug the HDD power cable to the HDD.2. Plug the FAN cable to controller board connector J21

32/55Upgrading of the Network Board Ass’y Software Perform the upgrading of the print server software according to the procedure shown below.1. Touch

33/554. Touch the Next Screen button once to display the next screen, and touch "System Software” button.5. Touch the Next Screen button to skip

34/557. Touch the Enter button without inputting any Keycode because it is already set. The printer starts processing to prepare the upgrading. (It ta

35/559. After finishing the Print Server upgrading, other upgrade screens (HCF*1, Container Stacker 2*2, Container Stacker 1, Print Engine-FPGA, Print

36/55Set IP Address of the Network Board Ass’y Perform the setting of IP Address according to the procedure shown below.1. Touch the Setup icon on Ma

1/551.OverviewInstallation Requirements The contents of the NIC kit are listed in the table below.PrinterNo ItemQuantity in DDP70/92 Quantity in EMP1

37/554. Touch “Network” button.5. Touch “10/100B-T NIC” button.6. Touch “IP Address” button.

38/557. Enter IP Address for user environment by using ten keys, and touch the Enter button.8. Touch “Exit ” button.Specify IP Address usingten keys.E

39/55Reset to Factory Default of the Controller configuration and the Network Board Ass’yCAUTION!When Factory Default is executed, please note that t

40/554. Click “Reset” button. 5. Check the “Complete Reset” and click the “Submit” button.ResetSubmit

41/556. After the above-mentioned operation is executed, the following screens are displayed in OCP of theprinter. Then execute power cycle the prin

42/554. The input screen of “Service Password” is displayed. Touch the Enter button to enter “Service” menu without inputting the Service Password (

43/557. Touch the Enter button, then the screen shows the Backup processing.Note:The Backup time will take approx. 1 minutes.8. Touch the Exit button

44/55Table2. Printer setting value list reset in initial value by Factory DefaultItems Factory DefaultOCP：Printer MenuDefault Paper Source AutoSelectS

45/55Continuation of Table 2Items Factory DefaultPrint Errors EnableBest Fit EnableJob TimeOut 0PostscriptHafltone Density *4 MediumWide A4 DisablePCL

46/55Continuation of Table 2Items Factory DefaultPostScript I/O Mode TBCP^C Response EnableDefault PostScript *2Paper Color WhiteChannel Name lpEmulat

2/552.Installing for the DDP70/92Print the Status Page Please print the Status Page in order to confirm the printer works normally before installing

47/55Continuation of Table 2Items Factory DefaultPage Orientation PortraitPage Length (5 - 127) 60Line Termination CR->CR-LF ; LF->CR-LF ; FF-&g

48/55Continuation of Table 2Items Factory DefaultChannel Name postscriptEmulation PostScriptProtocol 3102Spooling *3 NoneLPD Banner Page DisableGenera

49/55Continuation of Table 2Items Factory DefaultPage Orientation PortraitPage Length (5 - 127) 60Line Termination CR->CR ; LF->LF ;FF->FFLin

50/55Continuation of Table 2Items Factory DefaultPaper Source Auto SelectPaper Size Letter LEFPaper Type PlainPaper Output Auto SelectCopies(1-999) 1C

51/55Continuation of Table 2Items Factory DefaultPostScript I/O Mode Normal^C Response Enablelp_landscape PostScript *2Paper Color WhiteChannel Name p

52/55Continuation of Table 2Items Factory DefaultPage Orientation PortraitPage Length (5 - 127) 60Line Termination CR->CR ; LF->LF ;FF->FFLin

53/55Continuation of Table 2Items Factory DefaultPaper Source Auto SelectPaper Size Letter LEFPaper Type PlainPaper Output Auto SelectCopies(1-999) 1C

54/55Continuation of Table 2Items Factory DefaultTime Server (Primary) (blank)Time Server (Secondary) (blank)Synchronization Time 0Set Manually Enable

55/55Continuation of Table 2Items Factory DefaultWeb：Service - Configuration MenuPreventiveMaintenance WarningCheck Box DisablePercent 75PreventiveMai

3/55Removing the I/O Panel Ass’y1.Remove the two screws①(M2.5x8 Pan Head Screw), and remove the Dust Cover/D Sub Type and Serial Connector Cover.2.R

4/553.Attach the Dust Cover/D Sub Type(Installation Requirements No.3) to the MGMT of the Network Board Ass’y, and attach the Dust Cover/Modular Typ

5/55Confirmation of Connection1. Power on the printer, and touch “Information” button after “Ready” is displayed on the OCP.CAUTION!When turning on th

6/553.The input screen of “Service Password” is displayed. Press the Enter button to enter “Service” menu without inputting the service password(fact